ALESIS MULTIMIX 4 USB SETUP BLUETOOTH
Antenna – Adjusts the reception of the signal that is being received from a Bluetooth source such as a PC, Mac, iOS device, Android®, etc.).Ħ. Phantom power is applied to the XLR microphone inputs.ĥ. Phantom Power Switch – Provides phantom power Power ON/OFF Switch – Turns MultiMix 10 Wireless’sĤ. Selecting an improper voltage setting can damage the unit.ģ. Voltage Selector* – If your unit has a voltage selector switch, change its setting only when necessary (e.g., when traveling to a country or region with a different voltage). Power Cable Input (IEC) – Insert the included powerĢ. Other trademarks and trade names are those of their respective owners.ġ. and any use of such marks by Alesis is under license. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. Phones Output – Connect headphones to this stereo 1/4” output. Phones/Monitor Knob – Adjusts the signal level sent to the Monitor Out and the Phones Output.Ģ0. Stereo Aux Return – Controls the signal level returning from the Aux inputs.ġ9.
![alesis multimix 4 usb setup alesis multimix 4 usb setup](https://asset.conrad.com/media10/isa/160267/c1/-/en/1283655_ZB_00_FB/image.jpg)
In, and the audio of a paired Bluetooth device.ġ8. Master Fader – Adjusts the speaker’s Main Out volume, which includes the Mic/Line inputs, Ext. LED Meters – Displays the audio signal level of the main outputs.ġ7. Pair LED – The Pair Status LED will illuminate when MultiMix 10 Wireless is paired with a Bluetooth audio device.ġ6. Pair/Unpair – Press the Pair/Unpair button to pair a Bluetooth® device or to disconnect a paired Bluetooth device.ġ5. Phantom Power LED – Indicates whether the phantomġ4. In Airplane Mode and deactivating any alarms Power LED – Indicates whether MultiMix 10 Wireless is We recommend putting your Bluetooth device Note: To avoid interruptions during playback,ĭisable the rear panel Mic 1 and 2 inputs. When front panel Mic inputs 1 and 2 are in use, this will The signal level isĬontrolled with channel faders 1 and 2, respectively. Mic Input 1/2 – XLR-1/4” combo inputs for use withĭynamic and condenser mics. The right speaker when adjusting the Balance controlĮxt In – 1/8" stereo line level input for channels 9 andĮxt Out – 1/8" stereo output that mirrors the main Stereo source and varies the relative level of theĬhannels, so that the left channel will not come out of The BalanceĬontrols are found on stereo channels which take a
![alesis multimix 4 usb setup alesis multimix 4 usb setup](https://s1.manualzz.com/store/data/001443456_1-ddfb4a0ecdb8d8248510fda5e3c60b82-360x466.png)
The right speakers or anywhere in between. Pan controls are found on monoĬhannels, sending the mono source to either the left or Pan/Bal (Balance) – Directs the output signal to the left Channel Fader – Controls the signal level of the Mic Aux 2 is ideal for sending a signal to outboard processors.ħ. Aux 2 is post-fader, meaning it takes the signal after theĬhannel fader position. Auxġ is ideal for sending a signal to monitors or headphone amplifiers.Īux 2 – Sends the channel’s signal to auxiliary processors, onstage monitors, or Lo EQ – Provides up to 15dB of boost or cut to the 80 Hz frequency range.Īux 1 – Sends the channel’s signal to auxiliary processors, onstage monitors, orĪux 1 is pre-fader, meaning it takes the signal before the channel fader position.
![alesis multimix 4 usb setup alesis multimix 4 usb setup](https://manualmachine.com/html/dd/dddb/dddbb56a41f165b1f7c3220ff9275e7a0ee7b30166f0f808deac02fdfef49462/htmlconvd-qmsJPt2x1.jpg)
Hi EQ – Provides up to 15dB of boost or cut to the 12 KHz frequency range. Clipping occurs when the powerĪmplifier is distorting and working beyond its limits. Note : Avoid amplifier “clipping” at all costs.
![alesis multimix 4 usb setup alesis multimix 4 usb setup](https://i.ytimg.com/vi/5mwj-aD9Syo/mqdefault.jpg)
Setting of the Gain knob or Channel fader. Peak LED – The LED will flash if the signal is clipping. Loudest passages and then back it down so it no longer peaks. Adjust this so that the Peak LED lights on the